Description
| Product Description | İt is a special epoxy resin based self spreading last floor system which has two component, not contain solvent. | |||||
| Product No | 706-1 | |||||
| Areas of Application | • Storage and installation areas,
• Maintenance workplaces • Multi-storey and underground car parks, garages and loading ramps • Hospital, drug factories, drug stores etc. In places, • Schools, Locker rooms, • Manufacturing, • Beverage and food industry, • Used in liquid impermeable , dust-free, chemically resistant and stable surfaces of areas requiring endurance to the floor finish which concrete, cement mortar surfaces exposed to normal, medium, heavy load |
|||||
| Characteristics/ Advantages
|
• Provides very good chemical and mechanical strength.
• Easily applicable. • It is suitable for spreading decorative flakes. • Fluid. • It is economical. • Liquid impermeable. • Provides gloss finish coating. • Non-slip surface can be obtained. • There is no volatile organic compound (VOC). |
|||||
| Brightness and Color | Bright, mat (Can provide in other RAL colors depending on demand) | |||||
| Mechanical/Physical Properties
|
Density
Total Solids Percentage Thinning Pressure Resistance Bending Strength Adhesion Strength Shore D Hardness Taber Wear Test 1 kg. CS 10, 1000 content Consumption |
1,40 kg/dm³
%100 Yok ~ 60 N/mm² (28 days / +23°C) ~ 30 N/mm² (28 days / +23°C) > 1.5 N/mm² (failure in concrete) ~76 (7 days / +23°C) ~ 80 mg ~1,40 kg/m² with a consumption of 1mm thickness is obtained. We recommend a thickness of 2-3 mm for optimum protection |
||||
| Curing Details | Moisture Ratio / Temperature | Food Traffic | Light Traffic | Taking full cure | ||
| %60 +10°C | 16 hours | 3 days | 10 days | |||
| %60 +20°C | 13 hours | 2 days | 7 days | |||
| %60 +30°C | 10 hours | 1 day | 5 Days | |||
| Chemical Resistance | Resistant is: Petrol, Beer, Cyclohexane, Diesel Oil, Ethanol 10%, Ethylene glycol, Glycerine, Milk, Sodium Chloride Solution 3-30%, Sodium Hydroxide 10%, Olive Oil, Paraffin, Petroleum, Castor Oil, Silicon Oil, Turpentine, Water and Soap
Partly durable is: Butanol, Ethanol, Methylisobutylketone, Perchlorethylene and Xylene.* There may be color change with the effect of chemicals. This research can be performed at room temperature. High temperature values and / or mixtures of chemicals can affect chemical resistance. |
|||||
| Surface Quality | Concrete substrates must be sound and have adequate compressive strength (at least 25 N / mm²) and tensile strength of at least 1,5 N / mm². The bottom surface must be clean. İt must be purified from such as oil, grease, coating and surface curing materials. | |||||
| Surface Preparation | Concrete substrates should be prepared using abrasive equipment to remove the cement slurry and obtain an open pore surface. Weak concrete must be removed, potholes, holes should be made completely clear. Substrate repairs, filling of orifices / holes and surface smoothening mixed with 0.02-0.2 mm quartz sand C PRIMER EP group should be made with the appropriate ones.
Concrete or screed surfaces should be primed or primed to obtain a smooth surface. All dust, loose and volatile particles should be removed from the surface, preferably with a brush and / or vacuum cleaner, prior to application of the product. |
|||||
| Application Terms and Limitations | Surface moisture content: <4% unit weight moisture content.
Test method: CM measurement or oven flow method. There should be no rising moisture according to ASTM (Polyethylene sheet test). Relative air humidity should be 80% maximum. Dew point. Be careful of condensation! In order to reduce the risk of condensation or bubble formation in the floor coating, the surface and uncoated floor temperature must be at least 3 ° C above the dew point. |
|||||
| Surface Temperature
Ambient Temperature Warmth of material |
Minimum+10°C, Maximum+ 30°C
Minimum+10°C, Maximum+ 30°C Minimum+10°C, Maximum+ 30°C |
|||||
| Mixing Tools / Mixtures | C SL EP must be thoroughly mixed with a low speed (300 – 400 rpm) electric mixer or other suitable equipment.
Mix component A mechanically in itself before mixing. After completely adding component B to component A, mix continuously for 2 minutes until a homogeneous mixture is obtained. After mixing components A and B, add 0.1 – 0.4 mm quartz sand and other fillers if necessary and mix for about 2 minutes until a homogeneous mixture is obtained. To make sure the mixture is done properly, remove the ingredients into another container and mix for 1 minute until a smooth mixture is obtained. Avoid excessive mixing to reduce air drag.
|
|||||
| Application Method / Equipment | Leveling:
C SL EP is poured onto the surface and spread evenly with the trowel. Then, after about 15 minutes (at + 20 ° C), the surface is roughened with a spiked roller to remove air bubbles. The application of the hedgehog roller must be done before 30 minutes (at + 20 ° C). Blurred System: C SL EP is poured onto the surface and spread evenly with the trowel. Then, after about 15 minutes (at + 20 ° C), the surface is roughened with a spiked roller to remove air bubbles. The application of the hedgehog roller must be done before 30 minutes (at + 20 ° C). Then it is extruded with quartz sand. Coating C SL EP can be applied as a coating, with a short pile roller (crosswise). Finishing coat The topcoat coatings can be spread with a spatula followed by a short pile roll (crosswise).
|
|||||
| System Structure | Protection of Concrete Floors:
Primer : 1 x C PRIMER EP Coating : 2 x C SL EP Textured Coating: Primer : 1 x C PRIMER EP 1st Floor : 1 x C SL EP 2nd Floor: 1 x C SL EP mixed with 2% Extender Thix. Self Leveling System 1,5 – 2,5 mm: Primer: 1 x C PRIMER EP Wearing Layer: C SL EP |
|||||
| Consumption / Dosage | Coating System:
Primer : C PRIMER EP 0,3 – 0,5 kg / m² Roller Coating: 2 x C SL EP 0,3 – 0,5 kg / m² for each layer.
Textured Coating: Primer : 1 x C PRIMER EP 0,3 – 0,5 kg / m² 1st Floor : 1 x C SL EP 0,4 – 0,5 kg / m² 2nd Floor: 1 x C SL EP 0,5 – 0,7 kg / m² Mixed with 2% Extender Thix (by weight).
Self Leveling System 1,5 – 2,5 mm: Primer : 1 x C PRIMER EP 0,3 – 0,5 kg / m² Wearing Layer: C SL EP 2,0 – 3,5 kg / m²
Diluted System approx. 4 mm: Primer: C PRIMER EP 0.3 – 0.5 kg / m² Basic Coating: 1 x C SL EP + quartz sand 0.1-0.4 mm (1: 1 mixture) 2.8 kg / m² Blunting: excessive blunting with quartz sand (0.4 – 0.7 mm) Finish Coating: 1 x C SL EP 0,8 kg / m² * The above values are theoretical and do not include additional material requirements depending on surface porosity, profile, leveling differences and loss. |
|||||
| Packaging | A + B Components: 12,5 or 25 kg. In ready-to-use sets
Big Pack Component A: 200 kg in barrels Component B: 200 kg in barrels |
|||||
| Shelf Life | Shelf life is 1 year from date of production if stored properly at room temperature, away from direct sunlight, between + 5 ° C and + 30 ° C. | |||||
| General Conditions | The above mentioned information was obtained with our careful research and experimentation in order to guide the application. Variety of materials and construction conditions cannot be controlled or affected individually. Incidents beyond our control are only limited to warranty on product quality. No warranties on application are implied other than manufactured product. This technical data sheet nullifies any prior technical data sheet. The quality and performance of the product is relative to the utilization technique. In case of a doubt a small test or getting technical support is recommended. | |||||
| Disposal | Empty packaging can be disposed of according to local and state regulations, or can be collected in recycling bins. Waste material must be disposed as construction waste after dried completely. Incinerating the waste product is dangerous. | |||||
| Safety Information | Keep products out of reach of children. Keep product sealed at all times. Using protective gear such as goggles and gloves is recommended. In case of skin contact the surface must be cleaned with fresh water and soap. In case of eye contact a physicians must be seen immediately. Further information can be obtained from safety data sheet. | |||||
Reviews
There are no reviews yet.