Skip to content Skip to footer
LRC
LRC
Close
LRC™ SC SH

LRC™ SC SH

This product is a cement-based chemical, and granule metric thin aggregate added material. It adds great strength to the surface against impact, and wear. It is applied on fresh concrete surfaces with molds.

Areas of Application:

  • Pool sides, touristic facilities, seashore walking paths,
  • Villas, subdivisions, and condominiums,
  • Pedestrian walks, sidewalks, parks, underground passages,
  • Parking garages, auto service centers, and gas stations,
  • Convention Centers, Malls, Commerce buildings, and all concrete surfaces.

Product Advantages:

  • It gives a natural stone look to the surface. It is decorative, esthetic, and colorful,
  • It is economic. The problems with natural stones such as high cost, limited colors, high permeability and wear, dusting, staining are nonexistent,
  • Creates a surface look that is free of cracks. With a protecting wax can have a shiny look,
  • Sticks very well to the below concrete, and it was designed to have an amazing surface strength,
  • It is suitable to indoors and outdoors applications, it does not stain,
  • It has a very low permeability compared to other concrete surfaces,

Since it is applied in blocks in the field you will not suffer from settling over time. You will not have unwanted weeds growing in between

SKU: 401-LRC SC SH Category: Tags: , , , , , , , , , Product ID: 6725

Description

Technical Data:

  • Color: Grey, red, green, brown, tan, and any special colors
  • Appearance: Colored thin powder
  • Packaging: 25 kg Paper Bags
  • Allowance to Traffic: Approximately 24-72 hours (depends on conditions)
  • Consumption: Depending on purpose of use and the weight of the
    traffic; approximately 3.5-5.0 kg/m2, on light color
    applications minimum 5.0 kg/m2 must be used.
  • Storage: In cool and dry areas shelf life is about 12 months.
    When stored maximum of 6 bags can be stacked on top of each other.
    should be stacked in a cool, dry environment with a maximum of 6 bags on top of each other.

Additional information

Surface Preparation

In order to obtain a solid surface and a healthy application the ground must contain 300-350 kg/m3 of cement. The concrete must have the right size aggregate. The concrete must be free of any admixtures. The slab thickness must be a minimum of 10cm. The concrete surface must be of a homogenous content, and with a wooden or magnesium spatula the surface must be leveled.
Application

LRC SC SH Application

Start the application once the footprint on the surface is 3-5 mm. There must not be too much water on the surface. Any excess water must be removed, and the surface must be moist. Using a spatula, the product must be distributed on to the surface. 2/3 of the material that will be used is spread on the surface homogeneously and waited for every part of it to become evenly moist (color change should be observed). Material is fed into the concrete by tray glazing and concrete integration is ensured. Rest of the 1/3 material part is spread on the surface homogeneously the same way and waited for every part of it to become evenly moist (color change). Then, it is fed into the surface and glazed.

Application of Mold Separator

After using LRC SC SH (on soft when pressed with finger but not wet surface) LRC SC RA (stamped concrete mold separator) is scattered on to the surface, and with the molds the stamping process will commence. The scattering process should be in the direction of the wind, and parallel to the surface. This process must be done at the thinnest possible way and piling should be avoided.
After the stamping process is complete the molds must be removed and rinsed and cleaned with water. The molds must be stored in a dry place. Molds that will not be used for a long time must be protected with talc or any other type of powder.
One or two days later the surface is washed with a pressure washer until the desired look it obtained. Since the timing of the washing is so important, it is crucial that it is done with proper equipment. Failure to follow the right instructions may result in the wrong color tone, scaling of the varnish, and loss of detail.

Protecting Varnish Application

After the washing process the surface left to dry. Before the application the surface must be cleaned and dust free. The surface must be dry. First layer of LRC POLISH 90 (Protecting Varnish) must be applied with a sprayer or brush. Do not use a paint roller. After the first layer is completely dry the second layer of LRC POLISH 90 can be applied. After the second layer is completely dry (approx. 2 hours) the surface can be used.
Things to pay attention

Never apply on wet and frozen surfaces
• It is flammable (R10), Keep away from fire and do not smoke.
• Do not inhale. On skin contact might create a rash. Do not swallow.
• Apply only in well ventilated areas.
General considerations

The above product information and explanations are based on our experience and the end result of our careful research. The diversity of the materials involved, the different construction and working conditions cannot be individually controlled or influenced by us. In non-control applications, the warranty status is limited only to the quality of the product sold. There is no guarantee for the application other than the production of the product. This technical paper invalidates the previous existing form. The quality of the work done may vary depending on your professional use of the product. If you are unsure, do a little test or get technical help.
Disposal

Empty packaging can be disposed of in collection boxes according to local-local regulations or recycling rules. After drying and hardening the used waste material, dispose of it as construction waste. It is dangerous to destroy product residues by burning.
Safety Information

Keep the products out of the reach of children. Keep the covers of the products closed. It is recommended to wear gloves and goggles during work. If the skin comes into contact with the material, it should be washed with soapy water immediately. In case of contact with eyes, seek medical advice immediately. For more detailed information, see the material safety data sheet.

Related products

We stand out with our experience and quality. We are here for you.

Address

297/5 Street, No: 1/2/1
Modern Evler Neighborhood
İskenderun / Hatay, Türkiye

Contact

info@lrc.com.tr

+90 326 502 52 53

Newsletter
[mc4wp_form id="186" element_id="style-9"]

LRC Kimya Ticaret © 2024. All Rights Reserved.

297/5 Street, No: 1/2/1
Modern Evler Neighborhood
İskenderun / Hatay, Türkiye

+90 326 502 52 53
info@lrc.com.tr